LEAK REPAIR KIT - WRAP SEAL QUICK REPAIR KIT FOR PIPE LEAKS
FEATURES:
- Repairs leak in 30 minutes
- Applicable to pipes up to 18″ (457 mm) diameter
- Applicable on any metal or non-metal pipes
- Repairs T-joint, elbow joint, valve thread, valve body
- Withstand pressure up to 400 psi (28 kg/cm2)
- Withstand temperature up to 200 °C (392 °F)
- Safe for drinking water and resistant to most chemicals
- Reinforce and strengthen pipe after repair
- Permanent repair and extend service life of pipes
APPLICABLE MATERIAL:
- Steel
- Copper
- Aluminium
- Galvanized steel
- PVC
- CPVC
- Stainless steel
- Polyethylene
- Polypropylene
- Cast-iron
- Concrete
- FRP/GRE
CHEMICAL RESISTANCE:
- Oil
- Water (drinking water, wastewater, steam)
- Solvents (acetone, toluene, MEK, ethyl alcohol)
- Mild acids (hydrochloric acid, sulfuric acid) and alkalis
- Chemical (ethylene glycol, xylenes, ammonia)
- Hydrocarbons
- Bases
- Slurries
- Fuels (petroleum, diesels, gasoline)
- Gases (LNG, LPG)
- Organic salts
WORKING TIME (FIBERGLASS TAPE):
- 1 minute at 30 °C (86 °F)
CURING TIME:
- 30 minutes at 30 °C (86 °F)
- Heat may be applied to decrease curing time
- Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.
APPLICATION:
- Pipe repairs
- offline repairs
- sealing joints
- hazardous material spill control
- reinforce thinning walls
- Abrasion protection
- Structural reinforcement
- Repairs in hard to reach areas
- Underwater repairs
OPERATING TEMPERATURE:
- Continuous – From -29 °C (-20 °F) up to 200 °C (392 °F)
- Intermittent – From 200 °C (392 °F) up to 320 °C (570 °F)
OPERATING PRESSURE:
- Recommended for pressure up to 400 psi (28 kg/cm2)
- (Results vary depending on pipe size, type of pipe, hole size, pipe content and method of application)
APPLICABLE INDUSTRIES:
TECHNICAL DATA
|
Pressure tested |
: |
1/2″
(15 mm) steel pipe with 1/8″ (3 mm) hole when repaired with Wrap Seal
withstands 4000 psi (281 kg/cm2) |
||
|
1/2″
(15 mm) steel pipe with 1/2″ (13 mm) hole when repaired with Wrap Seal
withstands 600 psi (42 kg/cm2) |
||||
|
Tensile strength |
: |
3920
psi (276 kg/cm2) |
||
|
Bond strength |
: |
230
psi (16 kg/cm2) |
||
|
Tensile elongation |
: |
1.2
% ± 0.7 % |
||
|
Compressive strength |
: |
13750
± 530 psi (967 ± 37 kg/cm2) |
||
|
Yield strength |
: |
2260
psi (159 kg/cm2) |
||
|
Cured hardness |
: |
82
Shore D |
||
|
Pipe size |
Number of rolls / size required |
|||
|
50 psi (4 kg/cm2) 10 plys |
150 psi (11 kg/cm2) 15 plys |
400 psi (28 kg/cm2) 20 plys |
||
|
½” (15mm) |
1 A |
1 A |
1 A |
|
|
¾” (20mm) |
1 A |
1 A |
1 A |
|
|
1″ (25mm) |
1 A |
1 A |
2 A |
|
|
1¼” (32mm) |
1 A |
2 A |
3 A |
|
|
1½” (40mm) |
2 A |
2 A |
1 B |
|
|
2″ (50mm) |
1 B |
1 B |
1 B |
|
|
2½” (65mm) |
1 B |
1 B |
2 C |
|
|
3″ (80mm) |
1 B |
2 C |
2 C |
|
|
4″ (100mm) |
1 B |
2 C |
3 C |
|
|
Pipe size |
Number of rolls / size required |
|||||
|
50 psi (4 kg/cm2) 10 plys |
150 psi (11 kg/cm2) 15 plys |
400 psi (28 kg/cm2) 20 plys |
||||
|
5″ (125mm) |
2 C |
2 C |
3 C |
|||
|
6″ (150mm) |
2 C |
2 C |
4 C |
|||
|
8″ (200mm) |
2 C |
3 C |
5 C |
|||
|
10″ (250mm) |
3 C |
4 C |
6 C |
|||
|
12″ (300mm) |
4 C |
5 C |
8 C |
|||
|
14″ (350mm) |
4 C |
6 C |
8 C |
|||
|
16″ (400mm) |
5 C |
7 C |
9 C |
|||
|
18″ (450mm) |
5 C |
8 C |
9 C |
|||
|
> 18″ (450mm) |
Contact SealXpert
for recommendations |
|||||
|
Roll size |
A (2″ x 5′) (50mm x 1.2m) |
A (2″ x 6′) (50mm x 1.8m) |
B (2″ x 12′) (50mm x 3.6m) |
B (3″ x 9′) (75mm x 2.7m) |
C (4″ x 12′) (100mm x 3.6m) |
|
WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:
PACKAGE:
- 1 roll of Wrap Seal Fiberglass Tape
2″ x 5′ (50 mm x 1.2 m)
2″ x 6′ (50 mm x 1.8 m)2″ x 12′ (50 mm x 3.6 m)3″ x 9′ (75 mm x 2.7 m)4″ x 12′ (100 mm x 3.6 m)
- 1 unit of Seal Stic Quick Cure Epoxy
- 1 pair of latex gloves
- Operating instruction
Post a Comment
Note: Only a member of this blog may post a comment.